Products: Industrial Chillers and Coolers
Industrial Refrigeration Systems and Turnkey Systems
Do you need a customised industrial refrigeration solution or a complete system, including accessories? We want to be your single point of contact and provide you with a varied range of solutions: industrial chillers, dry coolers and adiabatic coolers, temperature controllers.
Turnkey Refrigeration Plants
A refrigeration system is more than a single chiller: heat exchangers, hydraulic connections, additional cooling devices also come into play to support your production process.
Air-Cooled Liquid Chillers
In air-cooled liquid chillers, the cooling of the refrigerant gas is ensured by the ambient air itself. Frigofluid offers a wide range of this type of industrial chiller in its catalogue, including a solution with free-cooling.
For fluid outlet temperatures between 1°C and 20°C
-20 -10 0 10 20 30 40 50
RW ax Liquid Chiller
These liquid chillers combine efficiency and performance control with brushless axial fans: they are chillers suitable for achieving average fluid outlet temperatures while optimizing energy use. In standard execution, ambient temperatures up to +40°C are allowed, but set-ups for even higher ambient temperatures can be requested.
For fluid outlet temperatures between -8°C and 5°C
-20 -10 0 10 20 30 40 50
RW ax LT Liquid Chiller
Low outlet fluid temperatures (water or water and glycol, down to -8°C) characterize RW ax LT liquid chillers: air condensation ensures that they use are electrical energy, and not water, for their operation: a resource that is then optimized by the electronically controlled “brushless” type axial fans. Up to +40°C ambient temperature allowed in standard execution.
For fluid outlet temperatures between 10°C and 25°C
-20 -10 0 10 20 30 40 50
RW / EFC ax Liquid Free Cooling Chiller
The secret of this system is the combination of the refrigeration section and the free-cooling section depending on the time of day and year: the first mode allowed by these liquid chillers takes advantage of the normal operation of a refrigeration circuit, the second allows cold outside air to be directly conveyed to the fluid to be cooled: maximum efficiency, minimum energy use due to the clear separation between the two sections.
For fluid outlet temperatures between -12°C and 30°C
-20 -10 0 10 20 30 40 50
ERW ax Liquid Chillers
These liquid chillers are also suitable for working outdoors and in very high outside temperatures. Depending on the agreed design features, fluid outlet temperatures from -12°C to +30°C can be achieved: adaptability and reliability for all industrial plants.
For fluid outlet temperatures between 1°C and 25°C
-20 -10 0 10 20 30 40 50
RP Liquid Chiller with Environmentally-Friendly Refrigerants
High energy savings, low environmental impact, compliance with stringent European regulations: green RP model chillers, with R32 or R290 refrigerant, are the industrial refrigeration solution of the future. Small footprint and provision for remote control are Frigofluid's signature to these innovative equipment.
Water-Cooled Liquid Chillers
Cooling the refrigerant gas by means of a water exchanger: this is what characterises the water-cooled chillers, which use this feature to ensure high system efficiency. Frigofluid water chillers, with output temperatures down to -8° C, are ideal when air movement is not possible.
Industrial Dry Coolers and Adiabatic Dry Coolers
Industrial dry coolers are a useful solution where fluid outlet temperatures no lower than the external temperature are required. Adiabatic dry coolers are a version of these industrial coolers that can offer outlet fluid temperatures lower than the external temperature.
For fluid outlet temperatures between -10°C and 50°C
-20 -10 0 10 20 30 40 50
RAW/E Industrial Liquid Cooler
How to cool process fluids in the total absence of water? By employing industrial air coolers, or “dry coolers,” such as Frigofluid’s RAW/E series: simple, environmentally friendly, low acquisition cost.
For fluid outlet temperatures between 35°C and 50°C
-20 -10 0 10 20 30 40 50
MDC-F Table-Type Dry Cooler
MDC-F Dry cooler in “table” configuration is an efficient and cost-effective solution for cooling fluids in a variety of industrial settings, particularly for small and medium-sized plants. Its ease of use, and at low cost, makes it an advantageous choice for various applications.
For fluid outlet temperatures between 35°C and 47°C
-20 -10 0 10 20 30 40 50
MDC-V V-Type Dry Cooler
Ease of installation, operation and maintenance serving even large systems: this is the MDC-V “V”-shaped dry cooler. The distinctive design of the coils allows for greater heat exchange surface area than “table” dry cooler systems, all in an easily scalable solution.
For fluid outlet temperatures between 35°C and 50°C
-20 -10 0 10 20 30 40 50
PAD-V Adiabatic Cooler Condenser
Adiabatic liquid coolers and gas condensers PAD-V series are offered where the focus is particularly on rational use of water and energy thanks to a dual operating principle, during hot and cold seasons, and thanks to the control panel that optimizes system operating parameters.
For fluid outlet temperatures between 35°C and 50°C
-20 -10 0 10 20 30 40 50
PAD-XL W Adiabatic dry cooler
Maximum efficiency, minimum water usage: PAD-XL W is Frigofluid's proposed solution for adiabatic cooling of process fluids (typically water/water and glycol). It inherits the strengths of the PAD-V series, expanding its capabilities and offering even higher performance in terms of efficiency and savings. The smart choice for adiabatic cooling.
For fluid outlet temperatures between 35°C and 50°C
-20 -10 0 10 20 30 40 50
PAD-XS Adiabatic Dry Cooler
The PAD-XS is the ideal solution for process cooling and small (20 to 50 kW) industrial and HVAC systems. With its compact design, small footprint, and low noise, PAD-XS offers high performance with minimal environmental impact.
Adiabatic Dry Coolers
Frigofluid adiabatic dry coolers are cooling systems that use outside air to cool the fluid circulating inside their “finned coil.” Pre-cooling the air with short water wetting cycles (through the “adiabatic” section) allows for an increase in efficiency, typically needed during warmer times of the year, or in situations where the process fluid temperature must be lower than the outside air temperature.
Industrial Dry Coolers
Industrial dry coolers are closed-loop cooling systems suitable for applications requiring a process fluid temperature no lower than the ambient air temperature. Frigofluid can offer customers dry cooler systems in “table” or “V” configuration for different installation needs.These are compact solutions that do not require water use and are simple to operate and maintain.
Industrial Thermoregulation Units
Industrial termoregulation units manufactured by Frigofluid are designed to condition moulds and cylinders in various industrial processes. In plastic moulding, process fluids are kept at temperature, thus reducing the use of electrical power for heating and limiting the cooling power spent on cooling by self-stabilisation.
For fluid outlet temperatures up to 110°C
70 80 90 100 110 120 130 140
FT Water Thermoregulator
FT water temperature controllers make it possible not only to heat process water for molds, but also to stabilize the fluid for a long time at the desired temperature. Models available with oversized pump, suitable for high pressures.
For fluid outlet temperatures up to 140°C
70 80 90 100 110 120 130 140
FTT DC Water Thermoregulator
High temperatures, kept stable over time: FTT DC water temperature controllers take advantage of the principle of direct cooling by integrating with external water sources for long self-stabilization to benefit industrial processes. All with great ease of use, thanks to the touch-screen control panel.
For fluid outlet temperatures up to 90°C
70 80 90 100 110 120 130 140
FTT PD Water Thermoregulator
Pressure and vacuum working modes: this is the main feature of FTT PD water temperature controllers, especially useful for coping with some critical issues in production processes. The touch-screen panel also makes them very easy to operate.
Remanufactured Chillers
Remanufacturing is a 'hot topic' in industrial production, especially in times of resource rationalisation: Frigofluid can supply its customers with remanufactured chillers. A totally sustainable solution.
Industrial chillers, industrial coolers, temperature control units
Almost every industrial company needs to dissipate heat, but each production line has its own peculiarities: the temperatures at which the process fluid has to be handled and the resources to be used (water, electricity) change.
Our constantly updated list of industrial refrigeration and temperature control solutions takes these needs into account and includes
- industrial chillers, or industrial chillers, water- and air-cooled
- air coolers (dry coolers)
- adiabatic coolers
- temperature controllers
- customised industrial chillers
You can also ask for the installation of turnkey refrigeration systems, including chillers, auxiliary machines and design and installation services: Frigofluid will select and integrate for you the best solutions on the market, thanks to the collaboration carried out over time with reliable suppliers. And thanks to our participation in the MITA Group, an international team of cooling, industrial refrigeration and water treatment consultants.
Without ever forgetting the main component, namely our services at all stages of the project: design, installation, after-sales.
Resources
Plants and components
Find out all Frigofluid's productsComparing Different Technologies
Find out all the different technologiesFind out more
All technical articlesTools to help you choose
Customized Design
Custom Chillers and Turnkey Plants
Our Newsletter
Subscribe to the Frigofluid newsletter: stay up-to-date on technical solutions for industrial refrigeration and cooling and get to know our offer.